- 您现在的位置：买卖IC网 > Sheet目录538 > ZS-26-C (SMC Corporation of America)PANEL MOUNT ADAPTER PSE200
Series
PSE
Specific Product Precautions 1
Be sure to read before handling.
{ Pressure Sensor
Handling
Warning
{ Controller
Warning
Handling
1. Do not drop, bump, or apply excessive impacts (980
m/s 2 ) while handling. Although the body of the
sensor may not be damaged, the inside of the
sensor could be damaged and lead to a
malfunction.
1. Do not drop, bump, or apply excessive impacts
(1000 m/s 2 ) while handling. Although the body of
the controller case may not be damaged, the inside
of the controller could be damaged and cause a
malfunction.
ZSE ?
ISE ?
PSE
2. The tensile strength of the cord is 23 N. Applying a
greater pulling force on it can cause a malfunction.
2. The tensile strength of the power supply/output
connection cable is 50 N; that of the pressure
Z
I
SE3
When handling, hold the body of the sensor—do
not dangle it from the cord.
sensor lead wire with connector is 25 N. Applying a
greater pulling force than the applicable specified
PS
3. Do not exceed the screw-in torque of 3.5 N ? m when
installing piping. Exceeding this value may cause
tensile strength to either of these components can
lead to a malfunction. When handling, hold the
Z
I
SE 12
malfunctioning of the sensor.
4. Do not use pressure sensors with corrosive and/or
inflammable gases or liquids.
5. Connecting the sensor cable (Option)
Hold the female connector of the sensor cable with your
fingers and carefully insert it into the connector.
Sensor
Male connector
Female connector
A connector cover is provided as part of the cable assembly
(see the figure below). It is designed to keep the female
connector from slipping out of the sensor. To lock the connector
cover in place, first make sure it is facing in the right direction
as you slip it over the female connector, then lock it to the
sensor body by turning it clockwise. To remove the cover, first
unlock it by turning it counterclockwise, then pull back on it. To
remove the female connector, grab it with your fingers and pull
back on it. Do not pull on the cable.
Lock
Sensor
Connector cover
Unlock
Operating Environment
Warning
1. The pressure sensors are CE marked; however, they
body of the controller—do not dangle it from the
cord.
Connection
Warning
1. Incorrect wiring can damage the switch and cause
a malfunction or erroneous switch output.
Connections should be done while the power is
turned off.
2. Do not attempt to insert or pull the pressure sensor
or its connector when the power is on. Switch
output may malfunction.
3. Wire separately from power lines and high voltage
lines, avoiding wiring in the same conduit with
these lines. Malfunctions may occur due to noise
from these other lines.
4. If a commercial switching regulator is used, make
sure that the F.G. terminal is grounded.
Operating Environment
Warning
1. Our multi-channel pressure sensor controllers are
CE marked; however, they are not equipped with
surge protection against lightning. Lightning surge
countermeasures should be applied directly to
system components as necessary.
2. Our multi-channel pressure sensor controllers do
not have an explosion proof rating. Never use
pressure sensors in the presence of inflammable or
explosive gases.
3. Enclosure “IP65” applies only to the front face of
the panel when mounting. Do not use in an
environment where oil splashing or spraying are
anticipated.
ZSP
ISA2
IS ?
ZSM
PF2 ?
IF ?
Data
are not equipped with surge protection against
lightning. Lightning surge countermeasures should
be applied directly to system components as
necessary.
2. The pressure sensors do not have an explosion
proof rating. Never use pressure sensors in the
presence of inflammable or explosive gases.
16-3-19
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ZVN0124ASTZ
MOSFET N-CHAN 240V TO92-3
ZVN0540ASTZ
MOSFET N-CHAN 400V TO92-3
ZVN0545ASTOB
MOSFET N-CHAN 450V TO92-3
ZVN0545GTC
MOSFET N-CHAN 450V SOT223
ZVN2106ASTOB
MOSFET N-CHAN 60V TO92-3
ZVN2106GTC
MOSFET N-CHAN 60V SOT223
ZVN2110ASTOB
MOSFET N-CHAN 100V TO92-3
ZVN2110GTC
MOSFET N-CHAN 100V SOT223
相关代理商/技术参数
ZS-26-E-4
制造商:SMC Corporation of America 功能描述:Connector housing for PSE200
ZS-26-F
功能描述:SENSOR CABLE 3M FOR PSE530/531 RoHS:是 类别:传感器，转换器 >> 配件 系列:* 标准包装:1 系列:* 其它名称:Y92EEG18T
ZS-26-G
制造商:SMC Corporation of America 功能描述:SENSOR CABLE W/U-CLAMP(PSE53*)
ZS270
制造商:FORMOSA 制造商全称:Formosa MS 功能描述:1WATT SURFACE MOUNT ZENER DIODE
ZS270L
制造商:FORMOSA 制造商全称:Formosa MS 功能描述:1WATT SURFACE MOUNT ZENER DIODE
ZS270-LFR
制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:1WATT SURFACE MOUNT ZENER DIODE
ZS277
功能描述:浪涌抑制器 Module for 277Y
RoHS:否 制造商:Bourns 电压额定值:40 V 电流额定值:750 mA 工作温度范围:- 40 C to + 125 C 端接类型:SMD/SMT 封装 / 箱体:
ZS-27-A
制造商:SMC Corporation of America 功能描述:LEADWIRE, ISE30/ZSE30, 2 meter 制造商:SMC 功能描述:Plug-type connector, ZSE/ISE30